友情提示：在IBEW424工作而未通过学徒期的JOURNEYMAN将面临测试

td456

测试内容：
1。辨认线号
. i/ C% m4 u. t) {2.弯管
3.有关马达的知识
, L" c% i' T9 z% \( h; h2 S以上信息来自工会BUSINESS MANAGER: Tim Brower

望大家做好准备，不想太多的中国电工FAIL.

谁动了偶的奶酪

估计95％以上的中国电工都需要做这个测试吧？

一尘

只针对中国的电工，还是所有没经过学徒的电工？
我见过别的国家没经过学徒的电工，还有东南亚的华侨，理论技能一塌糊涂，完全凭经验干活。烤烤他们，准糊。
( d: L% s4 M0 V曾经一老兄，二十多年的journeyman，拿两个heater，串联接起来，说是一个heater太小，怕不管用。
+ k9 F7 z2 `8 P9 Z5 \+ B以前有一印度兄弟来我原先的工作单位应聘，老板拿了一节我握好的管子，问他能不能照做，老兄说能，然后双手握管，开始比划，然后就被客气的送走了。那个是铁管子，用手，doesn't work！不过，并不是所有电工都握管子，人家不干这行的，也来考，不公平。这又不是电工基本技能。听起来工会那些头头多是握管电工出身的。

NorthernWolfy

Very nice! It's going to be less 不公正的待遇.

MrElectrician

I understood that all electricians without any apprenticeship experience within Canada will be a test in union, the union then will give a training lesson to the electricians who fail the test, this is not just including Chinese Electricians, it includes all electricians from outside Canada.
2 B) K( W$ r+ p! X/ X, `
- Z9 g9 p* p7 A! u& H  XDoes anybody know this test is mandatory? Does the test is for everyone who already in Uinion or who will join the union, or both?
! G4 G, K" V7 |+ {; n
4 B: O: b" m  c$ w* ]' z: kThank you for your information!

td456

Actually we will have a meeting with  IBEW 424 president Jim in the middle of January.
, J1 S3 z8 {) d  j" K) T3 P; z+ AWe will present all those concerns and try to talk about this issue.
There are also some other issues we need to communicate with the Union.
% k3 o$ t2 i+ II will post my draft about those issues and ask for the feedback from our members.

NorthernWolfy

据我所知,所有的工会会员都要考和面试,不管你是申请加入还是老会员.这是对所有通过challenge test的所有人员.

今晚打老虎

fail了，结果会怎么样？

侠客行

目前工会还没有很明确的说法

海狸

这种考试有意义吗？见过不少有学徒经验的洋JOURNEYMAN一样不会弯管，不会接电机，到头来，还是没学徒经验的中国JOURNEYMAN给他们擦屁股。

MrElectrician

原帖由 侠客行 于 2009-1-4 10:12 发表
9 l- f: L" M- P, O' B  \& a3 f目前工会还没有很明确的说法

I heard at the meeting that if one failed the test, then the union will ask you to join the training lesson inside the union.
8 L8 j& Y- z; v1 S: A- Y4 `. H
Does anybody have the phone number of Barry or Jim ?

doo152

基本的弯管知识都有了标准示范，搜索conduit bending就好了。一般都是半寸的管子。至于机器弯管，我还没有操作过，也没在这个网站找到示范。没有相应经验的可以去看看。

td456

我有BARRY 或JIM 的电话，但我不知POST 在网上是否核合适。
$ o' y. ~  ?3 s0 P, x/ ^6 Z( ^给我发一短信。
5 l* ]5 b& B: s# v. }; ]有关机器弯管，一般是弯90度。机器的顶端都会一个TABLE,查一下对具体尺寸如3/4INCH的补偿量是多少，在管子上MARK那个尺寸，我记得对3/4INCH的管子好像是9INCH，将那个MARK对准机器上的箭头，按下按钮一直到指示到92度左右，因为管子会往回弹一些，然后再校正。若弯的不够90度放回机器，再弯多一点，若弯的过了90度，举起管子在弯角敲几下。再用大SQUARE　量一下，MATCH就好，若不MATCH,重复以上步骤。
文字表达有限。

MrElectrician

I think their phone number is open to public. Anyway I will call the union hall to get the number if you think it is not properly to post their number here.

td456

Barry Salmon: 780-462-5076(bus) 780-293-4424(cell)
+ L! |$ r1 K4 u0 @+ GJim Watson:   780-462-5076(bus) 780-220-1645(cell)

shstock

手工弯管子应该是568吧?
. n/ v$ b) Z" k5 K7 q: T
9 [7 B2 w# m) S* Z% D[ 本帖最后由 shstock 于 2009-1-5 11:01 编辑 ]