请问车子头顶的蓝色灯一直亮是怎么回事

zhanlixian · 发表于 2011-12-16 00:42

请问车子头顶的蓝色灯一直亮是怎么回事？因为正常情况下是一闪一闪的。
另外这两天发现无法用remote starter热车，请知道的朋友解答一下，万分感激！

scuba1995 · 发表于 2011-12-16 01:05

可能是你把遥控启动系统不小心搞成VALET MODE了。看看说明书，怎么出来。

kingsnake · 发表于 2011-12-16 08:56

本帖最后由 kingsnake 于 2011-12-16 09:02 编辑

我也試過，按了 hold ，還得上網查看每個按鍵的用途。
藍燈亮着説明警報系統還活着，但在reset 這個 hold 前，其它的按鍵暫時都被廢了。

zhanlixian · 发表于 2011-12-17 11:01

G:\DCIM\100CASIO\CIMG4373.JPG
因为是二手车，remote starter没说明书，请问要如何将它重置，有网站链接吗
非常感谢

zhanlixian · 发表于 2011-12-17 11:13

开车时蓝色灯就不亮了，请大家指点该如何操作，遥控器图如下

无栁先生 · 发表于 2011-12-17 11:16

不懂，帮顶

kingsnake · 发表于 2011-12-17 13:02

本帖最后由 kingsnake 于 2011-12-17 13:13 编辑

我的比你的簡單得多，但你的remote比較便宜

。

你的解決方法如下：
1. put key in and turn to igntion position (do not start car).
2. press 'LOCK' and 'TRUNK_OPEN' buttons simulaneously for 0.5 second ( note 0.5 no more then 1 second). ----done。
3. buy me a coffee.

NDT · 发表于 2011-12-17 15:25

老蛇，我的遥控器是这样的AUTOMATE EZSDEI476 RPN 476A

现在的问题是可以锁车解锁只是不能遥控点火，咖啡管饱让你扶着墙出去

scuba1995 · 发表于 2011-12-17 17:31

NDT 发表于 2011-12-17 15:25
# T% A9 {& V1 u. X) m, u0 s老蛇，我的遥控器是这样的AUTOMATE EZSDEI476 RPN 476A _- s. ?" N& b, w8 H* M! @- H2 W$ ~

8 F% z, D" |% _现在的问题是可以锁车解锁只是不能遥控点火，咖啡 ...

肯定是VALET MODE了，只要找到MANUAL, 知道怎么退出VALET MODE就可以。

scuba1995 · 发表于 2011-12-17 17:32

背面什么样，让我看看。请我吃烧鸭哈。

NDT · 发表于 2011-12-17 18:07

背面对你有用的东西可能是
FCC ID: EZSDEI476
RPN 476A 266 CODE
我猜想是进入了VALET MODE模式。上一辆车出现过这样的问题，在油门刹车上面有个拨动开关拨过来就好了。但是这个找不到手册也不知道具体型号，而且找遍了方向盘下面也找不到那个传说中的开关。还有就是本来是好的车停了两周忘了关灯回来的时候电池已经死翘翘了跳火以后发现按遥控点火可以闪灯能听见油泵工作的声音就是没有点火的动作。
应该是和下面是这个一样的
http://www.ebay.com/itm/EZSDEI47 ... hash=item48431d7564

scuba1995 · 发表于 2011-12-17 18:22

那两个都没用，需要型号。

NDT · 发表于 2011-12-18 08:28

在AM2接近，不知道具体型号有可能是AM1，安装时间大约是04年底应该是在GM dealer那里装的。我和制造商联系过，回复是不对个人做TROUBLE SHOOTING，让我和当地的DEALER联系。
下面是AM2的资料
http://www.automatecarsecurity.com/products/ke.asp

scuba1995 · 发表于 2011-12-18 11:22

try this:
1. Turn the ignition on.
2. Turn the ignition off.
3. Press and release the Valet
button within 10 seconds.

scuba1995 · 发表于 2011-12-18 11:28

also check this:

Pressing for one second arms the system by activating the
starter kill and locking the doors (if the door locks are connected).
The horn will honk (if connected) and the parking lights will flash
once to confirm arming of the system. While the system is armed,
the status LED will flash once per second. The Failsafe® Starter Kill
(if installed) will also prevent the vehicle’s starter from cranking.
Arming
© 2005 Directed Electronics—all rights reserved 9
The system can also be programmed to arm the optional Failsafe®
Starter Kill automatically (called Passive Mode). If the system has
been programmed for Passive Mode, the Failsafe® Starter Kill will
automatically activate 30 seconds after the ignition has been
turned off. After the ignition has been turned off, the status LED
will flash rapidly to indicate that the system is in Passive Mode.
If Passive Mode has been programmed on, then it is also possible
to program the system for Passive Locking. With Passive Locking,
the vehicle doors lock automatically at the same time that the Failsafe®
Starter Kill is activated. If Passive Locking is programmed on, care
must be taken to prevent the keys from being locked in the vehicle.
NOTE: For Passive Mode to be effective, the Failsafe® Starter Kill relay
must be installed.
Pressing for one second disarms the system and unlocks the
doors (if connected). The horn will honk twice (if connected) and
the parking lights will flash twice to confirm disarming of the system.
The optional Failsafe® Starter Kill will be deactivated. The status
LED will turn off, unless the system is programmed for Passive
Mode. In Passive Mode, the status LED will flash rapidly when the
system is disarmed. This indicates that the system will re-engage
the starter kill and re-lock the doors (if Passive Locking has been
programmed) in 30 seconds unless the ignition is turned on.
Disarming
10 © 2005 Directed Electronics—all rights reserved
If your remote transmitter is lost or damaged, you can manually
override the starter kill. To do this, you must have the vehicle's
ignition key and know where the Valet button is located. Be sure
to check with the installer for the location of the Valet button.
To override the starter kill, turn
the ignition on and press the
Valet button within 10 seconds.
The status LED will stop flashing
and the vehicle should start. If it does not start,
you may have waited too long; turn the ignition off and repeat the
process.
LOCATION OF VALET BUTTON_____________________________
You can prevent your system from automatically activating the
Failsafe® Starter Kill and locking the doors by using Valet Mode.
This is very useful when washing the vehicle or having it serviced.
In Valet Mode, the starter kill cannot be activated, even with the
transmitter, but all convenience functions (door locks, remote
start, etc.) will continue to work normally.

NDT · 发表于 2011-12-18 11:37

我的上一辆车这个开关是个拨动开关很容易找到。现在这辆车我试过几次都找不到那个Valet button，查过类似的遥控器手册说可能似乎和LED指示灯是一体的，我这个应该不是。

scuba1995 · 发表于 2011-12-18 12:34

看看是不是在天线上？

zhanlixian · 发表于 2011-12-18 21:09

kingsnake,我已经试过了，但是蓝色的灯依旧亮着，而且很不幸的，今天车子连用钥匙都启动不了，极度郁闷中······

kingsnake · 发表于 2011-12-19 09:02

zhanlixian 发表于 2011-12-18 21:09
* b7 h7 E1 w# Akingsnake,我已经试过了，但是蓝色的灯依旧亮着，而且很不幸的，今天车子连用钥匙都启动不了，极度郁闷中· ...

怎麽啦？連電池也完蛋了？
有些舊的遙控安全制，是安裝在車頭蓋下面的，很容易受到損害的，也都檢查一下吧。

zhanlixian · 发表于 2011-12-19 12:58

实在是不懂机械维修，哎

NDT · 发表于 2011-12-20 12:28

scuba1995 发表于 2011-12-18 12:34 " r# \8 r8 [! C L L
看看是不是在天线上？

不在天线上，看来只能去DEALER那里挨一刀了。

账号		自动登录	找回密码
密码			注册